We've developed a kit for the Yamaha FJ-07/FZ-07/MT-07 Tracer & MT-07: should we develop instructions? Email us at sales@mccruise.com
0

Your Cart is Empty

Cruise Control for Indian Scout Bobber [Throttle-By-Wire only]

Computer Mount Option
Switch Option
Diagnostic Dongle Patch Connection
(10% GST will be added in the cart f or Australian orders only)

This model is available in very limited quantities now.

NOTE: - This cruise control kit will NOT fit the Indian Scout or Scout 69, it will ONLY fit the Scout Bobber. 

The bike we used to prototype the cruise is a 2019 model, however we have also fitted a cruise to a 2014 Scout 69, and it is functionally the same, so to our knowledge this will fit all model years of the Scout Bobber.  We hope to release a Scout cruise control before November.

NOTE: - We currently have a very limited number of connectors for this model (less than 10 sets), When we run out of these we will not be able to ship until more are delivered, hopefully by late October 2020. 

The Motorcycle Cruise Control unit is adapted specifically for this vehicle, with a custom made and fully plug and play wiring harness, using genuine connectors and terminals as used by the manufacturer. There is no wire splicing or any other permanent changes made to your bike.

Cruise control computer mounting location.

  1. The cruise control computer is mounted inside the headlight cowl on the right side of the headlight shell. If your bike has a different cowl  or screen fitted to it, but still has the original headlight shell, the cruise computer will fit on the headlight shell, as long as there is space.  Please read the brochure for more details and photos.

  2. The cruise computer may be mounted in the same location as the Scout, in a special bracket low on the frame on the left side of the engine using the threaded mounting hole for engine crash bars.  There are two brackets available, one for bikes without crash bars, and another for bikes fitted with crash bars.  Please read the brochure for more details and photos.

    We have had a couple of customers asking about mounting the computer on the frame, under the fuel tank in front of the air filter housing.  With the standard air filter, there is not enough space to fit the cruise computer, however some have fitted an aftermarket air filter, and they say that this creates more space and the computer will fit there.  We have NOT seen these filters, and we have NOT fitted a cruise computer in this location.  The wiring harness provided with the cruise control option 2 (frame mount) should be long enough mount the computer under the fuel tank if desired.  We do not know if the computer really will fit in this location, how the computer can be mounted in this location or if this location may cause reliability issues with the cruise computer due to higher temperatures.

Cruise control switch - there are three options to choose from (see the photos):

  1. Our original MCCruise switch mounted on the mirror mounting post.  This mounting can use the mirror if it is fitted.  A suitable bolt and washer are provided in the kit to mount the switch if your bike has bar end mirrors fitted.

  2. Our original MCCruise switch mounted below handlebar.

  3. New Slim MCCruise switch mounted below the handlebar.  The mounting method is the same as used on the 2nd option above, but the Slim switch is used instead of our original control switch.  Please read the brochure (link below) for details about programming changes in the computer for this control switch which change which buttons are used for SET and RESume.

CAN-BUS Diagnostic Dongle Patch Harness

The cruise control connects to the bike's diagnostic connector.  In most cases this connector is fitted with a blanking plug, but some other accessories may also connects to the diagnostic plug.  If this is the case, a patch harness must be fitted to allow the cruise control AND the other accessory to be connected at the same time.  See the last page of the brochure (there is a link below) for more details.

Speed bump setting: The cruise computer is fully configurable by the user for either 1 or 2 km/h or 1 or 2 mph set speed change per SET/ACC or RES/DEC button press.

The electronic cruise control unit is shipped worldwide with all parts, parts list and detailed installation instructions for this kit.

  • Download the Brochure now:
    Click here for the vehicle brochure The electronic cruise control unit is shipped worldwide with all parts, parts list and detailed installation instructions for this kit.
  • Download the Parts List now:
    Click here for more information on this Motorcycle Cruise Control

CLICK HERE to see a list of installers.


    BEFORE ORDERING YOUR KIT:

    1. Please read the brochure to see how the cruise control will look on your bike.
    2. INSTALLATION MANUALS are no longer published on the web. However we urge you to obtain complete installation manuals from us before purchasing. That way you can review and assess whether to install yourself, or need to employ a professional. Please EMAIL US so we can provide all manuals and other important information about installation.
    Motorcycle Cruise Controls Reviews

    News & Updates

    Sign up to get the latest on sales, new releases and more …